How to Fix Out of Range Monitor Windows 10

The video card and computer monitor operate in harmony to generate the display. The video card generates the data, which is displayed on the Monitor. Each Monitor is intended to perform optimally at a particular resolution.

If the video card attempts to display a resolution that the Monitor cannot handle, an “out of range” notice or a blank screen will appear. The “out of range” notice indicates that the Monitor cannot display the specified resolution at the current time.

You might experience the one in practically all systems is one of the most prevalent errors associated with this issue. The input signals is out of range error. Fortunately, you may quickly resolve the issue by using one of the ways demonstrated below.

Our computers will not remain the same for long periods. It is vulnerable to both hardware and software evolution throughout time. When you purchase a new monitor, upgrade your graphics card, or install a new driver, you may get various issues.

While you can occasionally correct these faults easily, they can occasionally spiral into an impenetrable maelstrom.

Reason Behind this Issue

  • A new video card connected to an old monitor is the simplest cause of an “out of range” error. Newer video cards can support resolutions that are incompatible with older monitors. 
  • Inconsistent or corrupted drivers can also result in out-of-range displays on monitors, particularly under Windows. Another possible explanation for all operating systems is setting the resolution to a value that the Monitor was incapable of displaying.
  • This error can occur when the screen resolution is assigned to a value that exceeds the capabilities of the Monitor. For instance, if your Monitor supports resolutions up to 1920 x 1080 and your video card supports resolutions up to 2460 x 1440, adjusting the Monitor’s resolution to the video card’s limit will result in an Out of Range error.
  • One more reason for this error is that the refresh rate selected exceeds the capabilities of the Monitor. If you cannot synchronize the Monitor’s refresh rate with the graphics card’s, an “Out of Range” error is a foregone conclusion. Additionally, if the resolution is set to a standard value, ensure that the Monitor and its cables are completely connected.
  • If the error message is displayed on a secondary display, navigate to Windows Display properties and adjust the secondary display’s resolution setting to a lower value until the image appears. 
  • The optimal resolution and refresh rate for monitors are their native values. Excessive deviation from these values will result in an Out Range error and cause game-related issues. As a result, it is suggested to use the Monitor’s native resolution unless otherwise specified.

How to Fix Out of Range Monitor Error in Windows 10?

How to Fix Out of Range Monitor Windows 10

Try these fixes to Resolve this issue.

Remove or Update Previously Installed Graphics Drivers

  • The first method is fairly popular and straightforward among people experiencing this heinous issue. However, there are situations when this simple adjustment is insufficient, and you must continue troubleshooting in Safe Mode. Additionally, you will require the Windows 10 bootable USB device that you prepared in a prior way.
  • As the previous step explains, restart the computer from the USB stick or DVD and select Safe Mode.
  • Assemble a network connection, as we will be updating the drivers.
  • To enter the start menu, type system Manager and press Enter.
  • Navigate to the category of Display Adapters. Select Update DriverSelect with the right click on your graphics card. Skip the fifth step and click Remove device if you boot into standard Safe Mode without a network connection.
  • Automatically search for driver software and install by following the on-screen directions.
  • Restart your Monitor normally and verify that the issue has been resolved. Windows should locate and install it during startup if you uninstalled the driver.
  • If your issue has been resolved
  • Install the latest driver for your video card and operating System from the manufacturer’s website.

Using DDU, Delete and Reinstall the Graphics Card Driver

  • Display Driver Uninstaller (DDU) is a valuable program that paves the way for a clean driver installation by eliminating the registry and driver files gathered over time due to several displays installed on the computer, drivers updated regularly, and Windows updates.
  • Frequently, conflicts between or incorrectly installed drivers can result in resolution and refresh rate issues. Thus, removing the graphics drivers and then a clean install may be necessary to ensure a more comfortable and secure test environment.
  • Guide to Uninstalling Drivers Using DDU With its assistance, you may delete your video card’s driver, download an updated driver from your video card’s website, and reinstall it.

Change the Refresh Frequency or the Refresh Resolution in Safe Mode

Suppose you just installed a new graphics card or changed specific settings on your computer. In that case, it is conceivable that the graphics card or your PC is set to a refresh rate or resolution greater than the Monitor can handle, resulting in this vexing error number.

This issue is most prevalent among laptop users who use smaller monitors. The simplest approach to resolve this issue is to boot your computer into Safe Mode and change these settings.

The quickest and most effective way to resolve this issue is to start your computer in Safe Mode and modify these settings.

What Is the Safe Mode Setting?

Safe Mode is a Windows operating system emergency mode that enables the operating system to run with the bare minimum of settings, drivers, and programs. By deactivating user-made improper driver installations, application and System settings, and prohibiting the System from starting properly, the user can gain access to Windows and change the settings.

When the primary Monitor is not visible, these are primary techniques for entering your Monitor to Safe Mode:

Enter Monitor in Safe Mode by Using Windows Boot Drive

However, because your access to Windows is restricted due to the failure of our Monitor, you must attempt this efficient method of entering Safe Mode.

  • Turn on your computer and enter a bootable Windows 10 DVD or a properly configured USB device. It does not seem to be your original Windows 10 DVD, as you will only need it to access certain settings.
  • Start your computer immediately after insertion, boot from the drive you just installed, and follow the on-screen instructions.
  • Windows Setup should launch and prompt you to enter your language, time, and date settings.
  • After proceeding, click the Repair your computer option at the bottom and select Troubleshoot >> Advanced options >> Startup settings.
  • To start your computer in Safe Mode, press the number four key or F4.

Operation in Safe Mode

  • Once the machine has restarted and entered Safe Mode, right-click on the desktop and select Display Settings.
  • Adjust the resolution settings for your display by selecting the Settings menu and selecting the Resolution tab. 
  • Ensure that the setting is synchronized with the native resolution of your Monitor to determine whether the issue has been resolved. Then attempt a standard restart of your machine.
  • If none of the resolution options corrected the problem: Return to safe Mode by right-clicking on your desktop and selecting Properties -> Settings tab -> Advanced select, and then Monitor Navigate to the tab. 
  • Reduce the refresh rate if it is set too high. Take note that the suggested minimum frequency setting is 60 Hz. Because most panels have a default refresh rate of 60 Hz, you can experiment with this value.
  • Verify that the issue has been fixed.

Enter Monitor in Safe Mode by Using Second Monitor

This solution assures that you can activate Safe Mode without establishing a boot drive if you connect a second monitor. It is accomplished by following these steps:

  • Attach the second monitor to the computer using the VGA cable.
  • It would help if you turned the System should on. Click the Start menu when the screen appears.
  • Shift Restart by pressing and holding the key.
  • Wait until you reach the “Continue” or “Troubleshoot” screens before clicking “Turn off your computer.”
  • Continue to Troubleshooting -> Startup Settings and click Restart. 
  • When your computer boots, you can choose to boot in low-resolution video mode.
  • Remove the second Monitor and reconnect it to the main one.
  • Safe Mode has been activated.

Frequently Asked Question

What Does Input Signal Out of Range Mean?

It will appear on a normally blank screen. Assuming the data cable is connected properly, the video card provides the Monitor a signal stream that exceeds the Monitor’s capabilities.

How Do You Fix Input Signals Out of Range in Games?

If the issue is with the display settings or device drivers, boot into Safe Mode and make necessary changes in Device Manager. Safe Mode: Restart the machine. Reduce your video card’s resolution to your Monitor’s native resolution once in Safe Mode.

How Do I Fix My Out of Range Monitor Windows 10?

Restart by selecting Troubleshoot > Start-up Settings. When your computer boots, you can select option 3, which begins the computer in low-resolution video mode. Reconnect the primary Monitor. Once Windows has finished loading, revert to the chosen video resolution option.


When your Monitor displays the error “Out of Range,” this indicates that the computer’s output resolution is incompatible with the display. You may. Consider the solutions listed previously, such as reducing the resolution; this will significantly assist in resolving the issue. 

You can also resolve the issue by attaching another monitor, restarting the computer, or entering safe Mode with Windows Boot Drive. I believe that all of these solutions will assist you in resolving the Out of Range Monitor Windows 10 issue.